Dirt Devil Featherlite
Have you heard of the Dirt Devil Featherlite? Well, if you haven’t then it’s high time that you do.
The Dirt Devil Featherlite vacuum cleaner boasts of bag less operation and is a great choice if you want to clean those corners of your house that you cannot usually reach. The Dirt Devil Featherlite vacuum cleaner has a 12 amp motor and some onboard tools for cleaning. The weight of Dirt Devil Featherlite is less than 14 lbs and this means that you can carry it around your home with ease. Any discussion on an upright vacuum cleaner is incomplete without mentioning the ways in which a broken or worn out belt can be repaired. However you need to understand that changing the belt of a vacuum cleaner is not rocket science. In fact, because Dirt Devil Featherlite has quite a simple design changing a damaged belt is quite easy. Just about anyone can get the job done. You can easily get the replacement belts of you Dirt Devil Featherlite vacuum cleaner directly from the manufacturer or an online store. There are several authorized shops that repair Dirt Devil Featherlite vacuum cleaners and you can get the replacement belts from there as well. Read on to find out how you can change a Dirt Devil Featherlite belt.
How To Use Dirt Devil Featherlite
To replace the belt of your Dirt Devil Featherlite vacuum cleaner, you will have to first extend your vacuum and make sure it is in flat position. Next you will have to turn the vacuum upside down so that the bottom on the Dirt Devil Featherlite vacuum faces upwards. There is a plastic brush guard that is L-shaped in the Dirt Devil Featherlite. You will need to locate it and the three screws that hold the brush guard on to the base of the cleaner. Check the left side of the plastic brush guard, you will find the first screw right on the top. The next two screws are on the lower left and right of the brush guard. Use a good screwdriver to remove these screws from your Dirt Devil Featherlite cleaner. Lift the end potion of the plastic brush guard of the Dirt Devil Featherlite in order to remove it. Next you will have to remove the brush roll of your Dirt Devil Featherlite. To remove the brush roll you need to lift it up straight and slide off the old belt from the left. Clean the brush roll properly and remove all the dirt and dust from it. Once you clean the brush roll properly, set it aside along with your other Dirt Devil Featherlite accessories.
New Belt To Your Dirt Devil Featherlite
To place a new belt on your Dirt Devil Featherlite vacuum you will next have to remove the old belt from the motor shaft. You can then discard the belt. Next you will have to slide one slide of your new belt over the motor shaft of the Dirt Devil Featherlite. You will see the receded pulley part of your roll brush; install the other side of your belt onto it. While doing this, you need to be a bit careful. You will have to take care that the other side of your belt does not slide off the motor shaft of the Dirt Devil Featherlite. The other end of the belt should not move either. Once that is done you will need to reinstall the brush roll of the Dirt Devil Featherlite that you had previously removed. Then the squared ends of the brush rolls will have to be lined up and to the squared mounting points. This will ensure proper installation. Then you will have to line up the tabs of your brush guard to all the corresponding slots at the base of the Dirt Devil Featherlite vacuum cleaner. Press the plastic brush guard to get it back in place. Replace the mounting screws and flip the Dirt Devil Featherlite back to its position.
Technical Side Of Dirt Devil Featherlite
Like all other vacuum cleaners, some basic problems can arise with Dirt Devil Featherlite. However the good news is, with Dirt Devil Featherlite you can take care of most of problems without professional help. So, let’s take a look at some basic problems that can arise with Dirt Devil Featherlite and how you can fix it. If your Dirt Devil Featherlite vacuum cleaner refuses to operate or turn on check whether the vacuum cleaner is connected to a power supply that is working. Check the breaker or the fuse if needed. You might need to reset or replace it. If there is a problem with the suction of the Dirt Devil Featherlite, check if there is any dirty water in the tank. If there is, empty the tank. To empty the tank you will have to turn off the cleaner and grab the top of the tank. Pushing the latch will release the tank. Pull hard to get the tank off the base. Then you can easily remove the lid and drain out the dirty water. Once that is done you can replace the cap of the tank and attach the front part of the tank to the machine base. You need to make sure that the nozzle and the cleaner base is at the same level. Then get the water tank of the Dirt Devil Featherlite back in position.
Other Tips About Dirt Devil Featherlite
If water is leaking from the cleaner of the Dirt Devil Featherlite, you must check the dirty water tank. Empty the tank if there is a need. Open the latch of the solution reservoir of the Dirt Devil Featherlite and pull it forward. Fill the Dirt Devil Featherlite brand cleaner to the mark. Then fill the remaining reservoir with hot water. Once the water is filled close the cap. Then replace it on the base unit. While checking the Dirt Devil Featherlite, make sure that the solution reservoir is fixed firmly to base unit in case no cleaning solution is dispensed from the unit. If the level is low you will need to fill the tank with water and cleaner. If your Dirt Devil Featherlite carpet cleaner does not function properly, check the nozzle and the hose of the cleaner. If there are any blockages you must remove them immediately. If you follow these simple instructions, your Dirt Devil Featherlite will work just fine.



